Nashville™ 112 Operation Manual. Before using this appliance, read the operating guide for further warnings. Congatulations on your purchase of the Peavey Nashville 112. As the leader in steel guitar amplification, we are proud to offer you this smaller, more portable, lightweight cousin to the popular Nashville 1000. Page 1 AIASHVillETM WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE, READ THE OPERATING GUIDE FOR FURTHER WARNINGS. Page 2 INPUTS (1) The Nashville 400 has two inputs, one featuring high gain and the other one third as much gain. The High Gain Jack is the input normally used, unless a.
P > Peavey
Please select your desired model below. We have 95 Peavey Diagrams, Schematics or Service Manuals to choose from, all free to download!
Peavey Musician 400 Manual
|
|
Rendered in 0.0222 seconds
Disclaimer
Brand names and product names are the property of their respective owners. This Website contains a compilation of information already available elsewhere on the internet and therefore considered to be in the public domain.
We make every effort to ensure the information contained here is as accurate as possible, but we will not be responsible for any errors or omissions, or anything resulting thereof. All information on this website is supplied free of charge, in good faith and without warranty. E&OE.
All the downloadable content on this website has been scanned thoroughly for viruses. However, we do not accept any liability for any loss, damage or inconvenience, of any kind, as a result of downloading any information from this site. Always scan any information downloaded from the internet with an up to date virus scanner before opening the downloaded information.
The Peavey Renown 400 guitar amp is a solid state amplifier released in the late '80s. Solid state technology was still relatively new during the '80s, and Peavey was one of the first amplifier manufacturers to make production model solid state guitar amplifiers. The Peavey Renown 400 is known for its durability and extreme loudness.
Power Amp Section
The Peavey Renown amplifier is power rated at 210 watts into a 4 ohm load. The power amp clips at 130 watts into 8 ohms and 210 watts into 4 ohms. The owner's manual states that splitting the load to 2 ohms is not recommended. The Peavey Renown 400 had less than .5 percent total harmonic distortion. The Renown has greater than 95 decibels below rated power hum and noise. The domestic (U.S.) power consumption is 600 watts, 50/60 hertz, 120 VAC.
Preamp Section
The high-gain input of the Peavey Renown 400 has a high Z, 200 K ohms impedance. The high-gain input's nominal level input is -26 dBV, 40 MV RMS, the minimum input level is -46 dBV, 5 MV RMS and the maximum input level is 4 dBV, 1.5 MV RMS. The low-gain input of the Peavey Renown 400 (-6 dB pad) has a high Z, 44 K ohms impedance. The low-gain input's nominal level input is -22 dBV, 80 MV RMS, the minimum input level is -40 dBV, 10 MV RMS and the maximum input level is 10 dBV, 3 MV RMS.
Peavey Nashville 400 Specs
Front Panel
The front panel of the Peavey Renown 400 has a high-gain and a low-gain input at the left end of the panel. To the right of the inputs is the lead-gain section which includes a pregain knob (with a pull feature for a brighter sound), a saturation knob and a post gain knob. To the right of the lead gain knobs is the lead channel equalization section which includes the low, mid (with a mid-shift option that allows you to choose which frequencies the mid-knob controls), high and presence knobs. To the right of this section is the normal gain section with pre-gain (again with a pull feature) and the post gain knobs. To the right of the normal gain is the normal equalization section which includes the low knob, the pyramid knob (an active control that shapes the mid frequencies), the shift knob (which designates the frequencies that the pyramid knob controls) and the high knob. The last knob is the master volume knob. On the far right of the amplifier is the ground switch and the power switch.
Rear Panel
Peavey Nashville 400 Settings
The rear panel of the Peavey Renown 400 amplifier includes the power cord at the far left of the panel and a series of jacks on the right side of the panel. The jacks are a pair of paralleled speaker jacks, a power amp in jack, a pre amp out jack and a foot switch jack.